| | |  | Jewelry | Home » » Rotary Tool Holder Stand For Dremel Flex Shaft Clamp-On | | | | | | | Description: | | Adjustable Flex Shaft Holder Great for Holding Tools. This is a new adjustable flex shaft holder. This conveniently holds tools, which conserves valuable workspace. Includes two wire hangers that swivel 360. It clamps directly to tables or workbenches up to 2 3/8" (60 mm) thick. The height adjusts up to approximately 26 3/4" (67.945 cm) above the work bench. FindingKing works hard to update our descriptions and pictures of our merchandise. As part of a process of ongoing innovation by our suppliers, newer versions of the item shown may be shipped before we are able to complete an update. As a result there may be a slight variation in color and design. | | | Product Details: | | | Product Length:
| 0.0 inches | | Product Width:
| 0.0 inches | | Product Height:
| 0.0 inches | | Package Length:
| 16.2 inches | | Package Width:
| 3.9 inches | | Package Height:
| 3.7 inches | | Package Weight:
| 0.9 pounds | | Average Customer Rating:
|  based on 8 reviews |
| | | | Customer Reviews: | |
Average Customer Review:
 ( 8 customer reviews )
Write an online review and share your thoughts with other customers.
Most Helpful Customer Reviews
1 of 1 found the following review helpful:
 Great stand for DremelAug 27, 2010
By Mountainman 57
"MtnMan57"
Great stand. I use it fully extended and clamped to the right end of my workbench as I am right handed. I hang loose end of flex shaft on peg board on back of bench. My workbench is 4' long and this setup allows me to reach the 4" vise on the left side of bench. With this application the stand could not be any longer. I also used holes in base to screw into bench top for more support.
1 of 1 found the following review helpful:
 Not bad, but shortJul 29, 2010
By Carrington Wilson
"carringt0n"
The telescoping pole that holds the drill is only three short sections. The clamp is beefy and the pole seems as if it could take the weight if even higher so I'm not sure why the manufacturer didn't go one more length - if they had actually hung the Dremel from it with the flex shaft in place they would have immediately seen the problem. It is usable and the awkwardness of the length can be worked around. I've kept it and am using once in a while. It would be really annoying if I had to use it everyday.
Review of Amazon Rotary Tool HolderSep 28, 2011
By Helen M. Scovel
I thought it would go higher. I needed it to hold a Dremel with a Flex Shaft and it was not high enough. It is fine to simply hang something on, but not high enough to keep the shaft fairly straight so it works. I don't remember reading the height to which it could be adjusted, just figured it would go high enough since it was advertised as a rotary hanger and lots of people use Flex Shafts. Since it doesn't work for hanging the Dremel with a Flex Shaft attached and I was too lazy to send it back, I kept it to hang something else on in my work area.
 flimsySep 03, 2011
By Holly Bennett
If I could have given zero stars, I would have. This thing is so flimsy, I can't imagine it holding anything over a pound, much less a flex shaft motor. I have a Foredom flex shaft; I'm guessing the motor weighs around 5 lbs (total guess), and this table clamp bowed under the weight. There is no way that I could have ever used the flex shaft while attached to this holder as the normal "pulling" would have surely either caused my shaft motor to tumble to the floor or the clamp would have snapped. The "base" is made of plastic and I fully expect it would have cracked in a short matter of time. Probably good for holding helium balloons. Spend about $10 more and get a quality clip on from Rio Grande. Wish I had found them first.
Dremel Tool HangerMay 23, 2011
By R. Bobrowski
"MGB Owner"
The hanger works great, and the price was right. It offers good support for my dremel when using the flex shaft.
See all 8 customer reviews on Amazon.com
| | |
|
