| | |  | Assorted Tools | Home » » » Jiffy Jump Ring Jewelry Finding Making Jewelers Tools | | | | | | | Description: | | New Jiffy Jump Ring Tool. This is a new Jiffy jump ring tool. This highly versatile tool will produce round and oval jump rings in seconds. Swivels for wrapping wire into coil on one side and making accurate saw blade cuts on the other. Made for jewelers, silversmiths and crafters. This can make a large number of jump rings fast and easy. The saw blade guide allows you to cut jump rings straight. It can also be used to make straight cuts on watch bands, wire, tubing, ring shanks, etc. Made of stainless steel and silicone bronze. Holds items up to 15/16" x 1/4" (24 x 6.5 mm). It measures up to 4" (102 mm) long. You receive: 1 Jiffy jump ring tool 5 Rods that allow you to coil wire into round and oval jump rings easily 3 Round rods for round jump rings that each measure approximately 1/8" (3 mm), 1/16" (1.5 mm) and 3/32" (2.5 mm) in diameter 2 Rectangular rods for oval jump rings that measure approximately 3.2 x 1.4 mm (1/8" x 1/16") and 4.8 x 1.6 mm (3/16" x 1/16") 2 Screws for bench mounting 1 Instruction sheet. | | | Product Details: | | | Package Length:
| 7.0 inches | | Package Width:
| 2.0 inches | | Package Height:
| 1.0 inches | | Package Weight:
| 0.1 pounds | | Average Customer Rating:
|  based on 3 reviews |
| | | | Customer Reviews: | |
Average Customer Review:
 ( 3 customer reviews )
Write an online review and share your thoughts with other customers.
Most Helpful Customer Reviews
4 of 4 found the following review helpful:
 Pretty goodJan 03, 2012
By Ruth Tyler
"Ruthie"
The tool is smaller than what I imagined. It does not come with instructions but with a little finagling I figured it out.
I mounted mine on a small block of wood so that I could clamp it to my work station and put it away when I wasn't using it.
On one end is a large hole and the other a holding type piece.
There is a wing nut in the middle so you can swivel the tool around.
The 5 pieces that come with it are the pieces you wrap your wire around. 1st choose the size piece you would like to use. Then, on the side with the hole, unscrew the screw just enough to fit the piece, then tight the screw onto the piece.
If you are looking directly at the hole you will see a little flap with 3 tiny holes in it (bottom left). This is to hold the wire so that it does not spin while you tightly wined the wire around the piece/mandrel.
Place the tip of the wire into one of the 3 holes, tightly wined the wire around the mandrel. Remove the mandrel.
Swivel the tool around. Place the mandrel into the holder with the slot side up. Line up the slots on the mandrel with the slots on the holder then push the mandrel into the holder. Grab your jewelers saw with a fine blade, place two of your fingers strongly around the metal (from the bottom) one on each side with the slot still exposed. Start to saw gently.
Practice a bit and get your groove on how it works best for you.
Hope this helps.
6 of 7 found the following review helpful:
 Where are the instructions?Sep 23, 2011
By Shawn
I was excited to get this tool as I am a jewelry designer and make a ton of jumprings. But....Where are the instructions? There were no pictures, no written instructions and no help on the website. I think I'll buy the more expensive one next time as this was a complete waste!
3 of 3 found the following review helpful:
No instructionsNov 13, 2011
By Julie Aschenbrenner
"The dumber people think you are, the more surprised they're going to be when you kill them."
It would have been nice to receive instructions on how to work this tool. As it is, it sits on my workbench, never been used. I wouldn't have wasted my money.
| | |
|
